Alaska DMV CDL General Knowledge Practice Test 6

  • Questions50
  • Correct to pass40
  • Passing score80%
  • Minimum age18 years

50 questions. Pick an answer to see if it is right and why; you need 40 correct answers to pass.

  1. 1. What must the motor carrier do about a defect listed on a driver vehicle inspection report?

    Show answer

    Answer D: Repair it, or certify that repair is not needed, before the vehicle is dispatched again

    A reported defect must be corrected, or certified as not needing correction, and that certification is what the next driver reads before taking the vehicle.

  2. 2. What extinguisher rating is required on a vehicle carrying hazardous materials in amounts that need placards?

    Show answer

    Answer B: 10 B:C or more

    Placarded loads carry a much higher fire risk, so the required extinguisher rating rises to at least 10 B:C.

  3. 3. A commercial vehicle stops on the shoulder of a one-way or divided highway. Where do the three warning devices go?

    Show answer

    Answer A: At 10 feet, 100 feet, and 200 feet back toward approaching traffic

    Traffic arrives from one direction only, so all three devices are set back toward it at 10, 100, and 200 feet, and they must be out within ten minutes.

  4. 4. You stop to check the load. Which set of things are you looking at?

    Show answer

    Answer C: Tight tiedowns, cargo that has not moved, secure doors and tarps still fastened

    A cargo check covers the load and everything holding it: whether it has shifted, whether the devices are still tight, and whether doors and covers are still closed and fastened.

  5. 5. You have stopped and a pedestrian is waiting to cross in front of your truck. Why should you not wave the person across?

    Show answer

    Answer C: Another driver may not stop, and your wave sends the person into danger

    You cannot control what drivers in the other lanes will do, so you should not invite a pedestrian into a lane you do not command.

  6. 6. How can a driver tell that a shipment includes hazardous materials?

    Show answer

    Answer B: The shipping paper describes them and the packages carry hazard warning labels

    Hazardous materials are identified on the shipping paper with their shipping name and hazard class, and the packages themselves carry labels showing the hazard.

  7. 7. Compared with a fully loaded one, an empty truck under hard braking will often do what?

    Show answer

    Answer A: Need a longer distance to stop because traction is poor

    Stiff suspension and little weight over the tires reduce grip, so the wheels lock early and the vehicle can take longer to stop.

  8. 8. Your right wheels drop off the pavement onto a soft shoulder. What is the correct recovery?

    Show answer

    Answer A: Stay on the shoulder, ease off the accelerator, brake gently only once speed is down to about 20 mph, then steer back sharply and countersteer at once

    Bringing speed down on the shoulder first avoids a violent sideways jolt, and countersteering the instant the tires are back on the pavement keeps the vehicle out of the next lane.

  9. 9. You pick up a sealed trailer at a shipper. What should you check before leaving the dock?

    Show answer

    Answer B: That the seal number matches the paperwork and that the doors are properly closed

    You cannot look at a sealed load, but you can confirm that the seal is intact, that its number matches the documents and that the doors are secure.

  10. 10. What tells a driver when to shift up in a vehicle with a manual transmission?

    Show answer

    Answer C: Engine speed in rpm together with road speed

    Shift points are judged from engine rpm and road speed, using the operating range the manufacturer specifies for that engine.

  11. 11. Which of these is a suspension defect you must look for during the walkaround?

    Show answer

    Answer D: Cracked or broken spring leaves, loose or broken U-bolts, or leaking air suspension bags

    Broken springs, failed U-bolts and leaking air bags let the axle shift or the body drop, which can make the vehicle impossible to control.

  12. 12. Besides being uncomfortable, what can a series of hard, jerky brake applications do to a loaded combination?

    Show answer

    Answer A: Shift the load and push the trailer out of line behind the tractor

    Sudden, uneven braking can move cargo forward and upset the alignment of a trailer, which is why stops should be made smoothly.

  13. 13. What is the minimum passing score for every Alaska CDL knowledge test?

    Show answer

    Answer D: 80 percent

    The Alaska CDL manual states that the minimum passing score for all knowledge tests is 80 percent, and that a failed knowledge test may be retaken once per day.

  14. 14. A delivery van is stopped in the right lane ahead with its flashers on. What should you expect?

    Show answer

    Answer C: Someone may step into your lane from in front of it

    A stopped delivery vehicle hides the space in front of it, and that is exactly where a person carrying a package is likely to walk out.

  15. 15. Which situations call for a mirror check in a commercial vehicle?

    Show answer

    Answer A: Every lane change, turn, merge and tight maneuver

    Mirrors must be checked regularly and always before, during and after any movement that changes the path of the vehicle.

  16. 16. What is checked in step six of the seven-step method?

    Show answer

    Answer D: The turn signals and the stop lights, checked from outside the vehicle

    Step six returns to the cab to switch on the signal and stop lamps, then checks each one from outside, because those lamps are not lit during the earlier light check.

  17. 17. Two tires in a dual set have noticeably different diameters. Why is that a problem?

    Show answer

    Answer C: The larger tire carries more than its share of the load and can be overloaded

    The taller tire touches the road first and takes most of the weight, so it runs overloaded and hot while the smaller one does little work.

  18. 18. The engine has overheated and you need to check the coolant. What is the safe procedure with a pressurized radiator cap?

    Show answer

    Answer A: Shut the engine off, let the system cool, protect your hands, turn the cap slowly to its first stop so pressure escapes, step back, then remove it

    A hot pressurized system throws steam and boiling coolant out of the opening, so the pressure is released slowly and only after the engine has cooled.

  19. 19. You are driving past a park where children are playing close to the curb. What is the correct assumption?

    Show answer

    Answer A: A child may run into the street without looking

    Children act on impulse and do not judge traffic well, so a driver has to expect one to enter the road and slow down in advance.

  20. 20. Why is it harder to judge speed and distance at night?

    Show answer

    Answer C: You see much less detail and have fewer reference points

    Darkness removes the visual references that the brain uses to estimate distance and closing speed, so drivers routinely misjudge both.

  21. 21. You find a defect during the pre-trip inspection. What must happen before the vehicle is driven?

    Show answer

    Answer C: It must be repaired, or the vehicle must not be driven

    Writing a defect down does not make the vehicle safe; a defect that affects safe operation has to be corrected before the trip starts.

  22. 22. You can see a crack in a brake drum that runs across more than half the width of the friction surface. What does this mean?

    Show answer

    Answer C: The drum is defective and must be repaired before the vehicle is driven

    Cracks longer than half the width of the friction area mean the drum can break apart under braking heat and must be replaced.

  23. 23. After starting the engine, how quickly should the oil pressure gauge come up to its normal range?

    Show answer

    Answer B: Within a few seconds

    Oil pressure should build within seconds of starting; if it stays low, the engine is not being lubricated and should be shut down.

  24. 24. Which vehicles are most likely to get hung up on a raised railroad crossing?

    Show answer

    Answer A: Low-slung units such as car carriers and lowboys

    Vehicles with low ground clearance or a long wheelbase can bottom out on a humped crossing and become stuck on the tracks.

  25. 25. You hear air escaping from a trailer tire during the pre-trip. What should you do?

    Show answer

    Answer C: Have it repaired or replaced before the vehicle is driven

    An audible leak means the tire is failing now, and federal rules do not allow a vehicle to be operated on a flat or leaking tire.

  26. 26. How are the headlights, marker lights and turn signals checked during the seven-step inspection?

    Show answer

    Answer A: The engine is shut off, the parking brake is set, the lights are switched on and then checked from outside the vehicle

    The lights are switched on with the vehicle secured, then the driver walks around and confirms each lamp actually works and is clean.

  27. 27. On a tractor with a sliding fifth wheel, what does moving the fifth wheel forward do?

    Show answer

    Answer A: Puts more of the trailer weight onto the steering axle

    Moving the coupling point forward transfers weight from the drive axles to the steering axle, which is how a driver corrects a drive axle that is over the limit.

  28. 28. What is generally the safest speed in dense but freely moving highway traffic?

    Show answer

    Answer D: The speed of the traffic around you, up to the posted limit

    Crashes rise with the difference between your speed and the traffic around you, so moving with the flow within the legal limit is safest.

  29. 29. For a modern truck with low-friction parts and a streamlined shape, which gear should be used going down a grade?

    Show answer

    Answer D: A gear lower than the one needed to climb the same grade

    Newer trucks roll more freely than older ones, so the old rule of using the climbing gear no longer holds; a lower gear is needed for enough engine braking.

  30. 30. You normally pull an empty trailer, but today the same tractor is loaded to its legal maximum. What changes about getting under way?

    Show answer

    Answer A: You may need to start in a lower gear, since the load takes more pulling power

    The heavier the load, the lower the gear needed to get the vehicle rolling without lugging or stalling the engine.

  31. 31. A 40 foot straight truck and a 70 foot tractor-trailer make the same right turn. Which needs more room and why?

    Show answer

    Answer B: The tractor-trailer, because the longer the vehicle the farther inside the rear wheels track

    Off-tracking grows with the distance between the front and rear axles, so the longer combination cuts the corner much more sharply and needs extra room.

  32. 32. What should a driver assume about the height posted at a bridge or an overpass?

    Show answer

    Answer B: That it may be wrong, because repaving or packed snow can leave less clearance than the sign shows

    Resurfacing and packed snow raise the road under the structure, so the real clearance can be lower than the posted figure.

  33. 33. An unblocked crate 4 feet long and weighing 1,500 pounds needs at least how many tiedowns?

    Show answer

    Answer A: Two

    A short article that weighs more than 1,100 pounds requires at least two tiedowns even though it is under 5 feet long.

  34. 34. During the walkaround you find the reflective conspicuity tape along the trailer caked with road grime. What should you do?

    Show answer

    Answer B: Clean it, because dirty reflective material cannot make the trailer visible at night

    Reflective sheeting only works if light can reach it and bounce back, so a dirty strip leaves the trailer effectively unmarked to approaching traffic.

  35. 35. An oncoming vehicle at night has bright headlights that are making it hard to see. What should you do?

    Show answer

    Answer B: Look toward the right edge of your lane and avoid looking directly at the lights

    Looking at the right edge of the road keeps your eyes off the glare while you stay in your lane; glare can leave you nearly blind for several seconds.

  36. 36. Which of these is a major cause of skids in heavy vehicles?

    Show answer

    Answer C: Over-braking, over-steering, over-acceleration or driving too fast for conditions

    Skids happen when the tires are asked for more grip than the road can give, which happens through braking, steering or accelerating too hard or simply too much speed.

  37. 37. Part of your load stands high enough to hide a rear lamp or a reflector. What must be done?

    Show answer

    Answer B: The load must be moved or extra lamps fitted so the required lights can be seen

    Required lamps and reflectors must remain visible; if the cargo blocks them, the load is rearranged or additional lamps are fitted so the vehicle can still be seen.

  38. 38. During the engine compartment check, which leaks are you looking for?

    Show answer

    Answer D: Fuel, coolant, engine oil, power steering fluid and battery fluid

    Every fluid in the compartment matters, because a fuel leak is a fire risk and a loss of coolant, oil, steering fluid or electrolyte can disable the vehicle.

  39. 39. You are backing into a yard where electrical wires cross overhead. What is the main concern?

    Show answer

    Answer C: The wires may hang lower than the top of your vehicle

    Overhead space has to be checked like any other space around the vehicle, because wires and cables are often lower than they look from the cab.

  40. 40. The only way into a customer yard forces you to back toward the right, or blind, side of the vehicle. What should you do?

    Show answer

    Answer D: Use a helper and get out to check the path more often than you normally would

    Blind side backing is allowed but far riskier, so it calls for a spotter you can see and for repeated checks of the path on foot.

  41. 41. What does the gross combination weight rating cover?

    Show answer

    Answer B: The maximum loaded weight of the power unit together with the trailer or trailers it tows

    The combination rating takes in the power unit and everything behind it, loaded, as specified by the manufacturer.

  42. 42. On a multilane highway, which lane should a heavy vehicle normally use?

    Show answer

    Answer A: The right lane, except to pass or where signs direct otherwise

    Keeping right leaves the faster lanes free and reduces the number of vehicles that have to move around a slower, heavier vehicle.

  43. 43. While double clutching, what goes wrong if you take too long between the two clutch movements?

    Show answer

    Answer A: Engine speed falls too far and the gear becomes hard or impossible to engage

    Double clutching only works while engine speed and road speed still match; a slow shift lets rpm drop away and the gear will not go in.

  44. 44. What are you checking on the mud flaps during the walkaround?

    Show answer

    Answer C: That they are securely attached, not torn and not dragging on the ground

    A flap that is torn or hanging loose stops shielding following traffic from spray and stones, and a dragging flap can catch and tear away on the road.

  45. 45. What is the risk when too little weight rests on the drive axles?

    Show answer

    Answer A: Poor traction, so the drive wheels spin easily on wet or slippery surfaces

    Traction depends on weight pressing the driving tires onto the road, so a light drive axle spins on wet, snowy or loose surfaces.

  46. 46. What is the main purpose of a retarder fitted to a heavy vehicle?

    Show answer

    Answer B: To help slow the vehicle and reduce the need to use the service brakes

    Exhaust, engine, hydraulic and electric retarders all slow the vehicle so the brakes stay cool and wear less, especially on grades.

  47. 47. When a helper guides you while backing, what should be agreed on before you start?

    Show answer

    Answer D: A set of hand signals, especially the signal that means stop

    The driver and helper must agree on signals in advance, above all the stop signal, because they usually cannot hear each other.

  48. 48. Which wheel or rim condition must be treated as a defect during the walkaround?

    Show answer

    Answer C: Cracks, illegal welded repairs, or missing and loose lug nuts

    Cracked or welded rims and missing or loose fasteners can let a wheel separate from the vehicle and must be corrected before driving.

  49. 49. An oncoming vehicle drifts across the center line into your lane. What is usually the safest move?

    Show answer

    Answer C: Steer to the right, toward the shoulder if necessary

    Moving right keeps you away from the drifting vehicle and off the oncoming side; the other driver may swerve back and hit you if you go left.

  50. 50. Apart from the risk of stalling, why is rolling backwards when starting on an upgrade so serious in a heavy vehicle?

    Show answer

    Answer D: You can strike the vehicle behind you, which is often much closer than you think

    You cannot see how close the vehicle behind has stopped, and even a short roll back is enough to hit it.